A productive greenhouse still needs careful preparation when temperatures fall. Winterizing your greenhouse means reducing draughts, retaining warmth, checking the heater and making sure the covering can withstand rain, wind and prolonged exposure to sunlight. The right approach protects seedlings, herbs and ornamentals without creating a damp, unsafe growing space.
Australian conditions vary widely, so winter protection in Hobart or regional Victoria will look different from winter management in Brisbane or Perth. Cool nights, sudden frosts, high electricity costs and strong coastal winds all influence the best materials and routines. Angelo Bernacchi Greenhouse brings long-standing greenhouse experience from LaPorte, Indiana, where dependable seasonal growing systems have been part of the business since 1906.
Begin with the frame, doors, vents, benches and anchoring points. Tighten loose fasteners, replace cracked glazing clips and confirm that the door closes firmly. Small gaps around a base rail or vent can release valuable heat throughout the night, while a loose panel may flap until it tears during a windy spell.
Inspect the roof and gutters as well. Fallen leaves can block drainage, and pooled water adds unnecessary weight to the structure. In exposed areas such as the Adelaide Hills, coastal New South Wales or Tasmania, secure the greenhouse against gusty weather before installing a new plastic film. Poly sheeting works best when it is evenly tensioned rather than left loose.
Greenhouse poly film should be UV-stabilised and designed for horticultural use. Cheap, non-UV plastic may become brittle after a season in the Australian sun, particularly in Queensland or Western Australia. A reinforced polyethylene cover is often a practical choice where wind, pets or falling branches could damage a single-layer film.
Double-layer poly sheeting creates an insulating air space that slows heat loss. If your greenhouse has a frame suitable for two layers, use an inflation blower to keep the gap consistent. Avoid trapping folds or allowing the film to rub against sharp edges. Clear film provides strong light transmission, while diffused film spreads light more evenly and can reduce harsh midday exposure.
After fitting the plastic, seal overlaps with greenhouse tape or a purpose-made channel system. Do not rely on household adhesive tape for permanent repairs; heat, moisture and sunlight can cause it to peel quickly. Keep the film away from heaters, flues and hot surfaces, as polyethylene can soften or ignite when exposed to excessive heat.
A sealed greenhouse still needs fresh air. Open roof vents or side vents during sunny winter days to prevent condensation, fungal disease and overheating. In Australia, a bright winter morning can lift the internal temperature rapidly even when the night has been cold. Automatic vent openers are useful for growers who are away during the day.
A small greenhouse heater may be adequate for frost protection, while a larger growing house needs a unit with enough output to maintain the desired minimum temperature. Electric fan heaters are straightforward for many home growers, but check that the model is rated for damp environments and has a thermostat. Place it where air can circulate freely rather than directly against poly sheeting or foliage.
Gas and paraffin heaters require greater care because they consume oxygen and can produce moisture or combustion gases. Any fuel-burning appliance should have suitable ventilation and must be operated according to the manufacturer’s instructions. Never use an outdoor barbecue, patio heater or improvised burner inside a greenhouse. A qualified electrician should assess power points, extension leads and safety switches before winter operation.
Install a minimum-maximum thermometer at plant height, away from the heater and direct sun. This gives a more useful reading than a sensor fixed near the roof. Many plants tolerate a cool night better than a rapid temperature swing, so use the thermostat to maintain a stable minimum rather than repeatedly heating the space to a high level.
Thermal screens, bubble insulation and water-filled containers can help moderate overnight temperatures. Use bubble wrap made for horticulture so it does not shed residue or block too much light. Watering early in the day gives leaves and surfaces time to dry before evening, reducing the risk of grey mould. Mulching outdoor beds near the greenhouse can also protect roots; seasonal soil preparation guidance is available in this garden soil guide.
Group plants with similar temperature and humidity requirements. Frost-sensitive seedlings should stay away from the perimeter, where cold air collects, while hardy greens can occupy cooler benches. Raise pots off the floor and keep foliage from touching the poly cover, because cold, wet leaves are more vulnerable to disease.
Azaleas and rhododendrons need particular attention to moisture, airflow and root conditions during cool weather. Avoid placing them beside a heater where dry air can stress the foliage, and monitor the potting mix rather than watering by habit. For more plant-specific care, refer to azalea care advice and adapt the timing to local Australian conditions.
Check the poly covering after every major wind event, especially on rural properties or exposed blocks. Look for stretched sections, loose battens, punctures and water collecting in roof dips. Small tears can often be repaired with compatible greenhouse film tape, but widespread brittleness indicates that the sheet needs replacement rather than another patch.
Record overnight temperatures, heater run time and condensation levels for the first few weeks. This helps identify whether the cover is leaking warmth, the heater is undersized or ventilation is insufficient. In areas with bushfire risk, keep dry vegetation away from the greenhouse, maintain clear access around the structure and follow local fire restrictions when using any fuel-burning equipment. A clean, secure cover and a correctly installed heater provide a dependable foundation for winter growth.